東陽學校運動場地坪***400-0709-910（請撥打400-0709-910電話,手機純屬私人號，請勿聯系。）

ensive molecular weight epoxy material. Finally, after all the preparatory work is completed the other approach can check the moisture content.
     Each step interval time, since the workshop is a continuous production, the need to protect the floor, prevent the entry of salt gray, pink layer
     Product protection
     After coating and topcoat construction in the ground. Epoxy resin material and hardener adequate response will take some time, in case the same floor surface and the interior floor is completely curing time is different, the floor surface is substantially complete curing time for a floor inside fully cured earlier than local time 2 h. Many construction workers after hand contact with the floor surface found to have entered the region dried construction, so easy to cause disturbances inside curing resin floor, resulting in peeling between the base layer and the film.
Advantages of Waterborne Epoxy Floor
Advantages waterborne epoxy resin aqueous epoxy floor for its outstanding performance advantages, so prepared aqueous epoxy coating also has excellent performance, resulting in a large family of water-based products in an increasingly important position, experts say water-ring epoxy resin in environmental protection today, the prospects are very broad.
Waterborne Epoxy Floor
Waterborne epoxy resin refers to an epoxy resin in the form of particles or droplets dispersed in water as the continuous phase of the dispersion medium and worthy of a stable dispersion. Since the epoxy resin is a thermosetting resin linear structure, it must be added before the construction of waterborne epoxy curing agents, chemical cross-linking reaction occurs at room temperature, epoxy curing after changing the original nature of novolac becomes into insoluble and infusible spatial network structure, it exhibits excellent properties. Waterborne epoxy coatings have many advantages in addition to solvent-based epoxy coatings, one adaptable to numerous substrates with high adhesion and excellent corrosion resistance coating面涂施工時粉塵（包括夏季蚊、蠅）等污染物對環氧面涂的污染。采取遮擋、粘貼等方法防止環氧面涂施工對現場其他成品及設備的污染。
質量要求
（一） 顏色一致、均一，無明顯色差，無漏光現象；
（二） 漆膜不得有以下明顯缺陷：起皮、縮孔、氣泡、小顆料、滾筒毛、裂紋、漏底；
（三） 陰陽角、倒角等復雜地形的處理，不能有遺漏及不平整現象，尤其各門口不能有堆積現象，門的開閉不會劃傷環氧面層；
（四） 施工現場干凈整潔：把灑落油漆、配漆的操作場所和超出施工范圍的涂層清理干凈，施工所使用的膠帶、報紙、壓條及其它廢棄物處理干凈。
五、應注意的質量問題
（一） 環氧砂漿起泡：進行施工前必須對地面的含水率進行測試，含水率過高將起泡，影響外觀質量。低于8%時方可進行施工環氧砂漿自流平面層。
（二） 面層有裂縫的痕跡：基層裂縫未進行處理，基層裂縫必須提成V 字型，用環氧砂漿填平。
（三）面層未硬化前嚴禁上人，禁止水泡，必須采取防水侵措施。
六、成品保護
（一）對樓梯口進行封閉，非自流平人員禁止入內。
（二）自流平地面未硬化前嚴禁上人作業。硬化后上人作業，嚴禁對地面進行劃傷，產生劃痕，影響外觀效果。
（三）施工時濺到墻上、官道上的材料及時進行清理。
（四）剛上人作業時嚴禁穿高跟鞋和硬底鞋作業。
（五）移動式腳手架及梯子必須底部采取措施，杜絕直接與地接觸。

七、環境保護及安全要求
(一) 現場拌制環氧砂漿處及時進行清理，防止濺到墻上。
（二） 環氧樹脂桶及時進行清理至室外，嚴禁隨層擺放。
（三）施工期間嚴禁在自流平施工作業面抽煙，以免引起火災及爆炸。
（四）基層打磨磨掉的混凝土粉塵用編織袋裝袋，運出。
基層混凝土施工要求
1．基層砼的強度應在≥C25，其水灰比盡可能小且夯中不能含有早強劑。
2．混凝土中最

資訊來源：4000709910